Technical Data
Cutting
Granito-LP Bridge Saw Blades
Granito-LP Bridge Saw Blades
Blade Diameter (mm) | Hard Granites (RPM) | Soft Granites (RPM) |
---|---|---|
350 | 1364 | 1637 |
400 | 1194 | 1433 |
450 | 1061 | 1273 |
500 | 995 | 1146 |
600 | 796 | 955 |
* wet use only
HS200 Bridge Saw Blades
HS200 Bridge Saw Blades
Diameter (mm) | PS (m/s) | min (RPM) | max (RPM) |
---|---|---|---|
400 | 32-35 | 1528 | 1671 |
450 | 32-35 | 1350 | 1486 |
PS = Peripheral Speed in metres per second, RPM = Revolutions Per Minute.
Marmo Bridge Saw Blades
Marmo Bridge Saw Blades
Blade Diameter (mm) | Coloured Marbles (RPM) | White Crystal Marbles (RPM) |
---|---|---|
350 | 2456 | 2729 |
400 | 2149 | 2388 |
450 | 1910 | 2123 |
500 | 1719 | 1910 |
600 | 1433 | 1592 |
* wet use only
DL200 Mitre Bridge Saw Blade
DL200 Mitre Bridge Saw Blade
Slab/Tile Thickness (mm) | Minimum (RPM) | Maximum (RPM) | Feed Rate m/min |
---|---|---|---|
3-5 | 1700 | 2100 | 1.5 – 1.8 |
8 | 1700 | 2100 | 1.2 – 1.5 |
12 | 1700 | 2100 | 1.0 – 1.2 |
20 | 1700 | 2100 | 0.6 – 1.0 |
30 | 1700 | 2100 | 0.4 – 0.6 |
Note: The feed rates shown above are recommended for straight cutting the majority of Sintered/UCS/Porcelain stones except Dekton® Aura and Dekton® Zenith. These materials should be cut at a maximum 0.50m/min on 20mm thickness.
When 45° mitre cutting any Sintered/UCS/Porcelain stones, the feed rate must be reduced by 30-40%.
Feed rates must also be reduced by 40-50% when entering and exiting the cut.
DL200 Mitre Blade must always be used wet, with sufficient water flow.
Pre-Cutting: Sintered/UCS/Porcelain stones must be cut on a flat solid wood or rubber bed/table, as the blade can blow out the stone when entering and exiting if the ends are mid-air/overhanging on a slatted bed.
Tension Cuts: All Sintered/UCS/Porcelain stone slabs need to be trimmed on all four sides to reduce tension. We recommend the thickness + 10mm (i.e. 20mm thick stone + 10mm = 30mm trimmed on all four sides) prior to cutting stone to template.
Tension cuts must be carried out in the following sequence:-
- First cut: One of the long edges.
- Second cut: One short edge in the direction of first cut.
- Third cut: The other long edge in the direction of second cut.
- Fourth cut: The remaining short edge (can be cut in either direction).
Quartzite Bridge Saw Blades
Diameter (mm) | Min Speed (RPM) | Max Speed (RPM) | Max Feed Rate (mm/min) |
---|---|---|---|
400 | 1300 | 1600 | 3000 |
450 | 1100 | 1400 | 3000 |
Note: Above parameters are for cutting 30mm thick stone in one pass, this can be increased for 20mm thick stone, subject to machine conditions and sufficient water feed.
SX200 Blades
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
115 | 9072 | 13300 |
125 | 7257 | 12000 |
150 | 6048 | 10185 |
180 | 5184 | 8730 |
230 | 3912 | 6790 |
Maximum cutting speed 80m/s.
S100 Blades
Diameter(mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
125 | 7257 | 12000 |
150 | 6048 | 10185 |
180 | 5184 | 8730 |
Maximum cutting speed 80m/s.
Flush Cut Blades
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
125 | 7257 | 12000 |
150 | 6048 | 10185 |
Maximum cutting speed 80m/s.
DL1 Blades
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
125 | 7257 | 12000 |
150 | 6048 | 10185 |
Maximum cutting speed 80m/s.
Double Sided Vanity Blades
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
125 | 7257 | 12000 |
Maximum cutting speed 80m/s.
Drilling
MB Core Drills
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
16 | 4300 | 4730 |
20 | 2860 | 3146 |
25 | 2290 | 2540 |
30 | 1910 | 2380 |
35 | 1630 | 2180 |
40 | 1430 | 1910 |
45 | 1270 | 1690 |
50 | 1140 | 1470 |
80 | 710 | 950 |
90 | 630 | 840 |
100 | 570 | 750 |
*Do not use on hammer setting.
VB Core Drills
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
15 | 4300 | 4730 |
20 | 2860 | 3146 |
25 | 2290 | 2540 |
30 | 1910 | 2380 |
35 | 1630 | 2180 |
40 | 1430 | 1910 |
45 | 1270 | 1690 |
50 | 1140 | 1470 |
*Do not use on hammer setting.
VB Mini Core Drills
Diameter (mm) | Recommended (RPM) | Maximum(RPM) |
---|---|---|
6 | 1950 | 2100 |
8 | 1950 | 2100 |
10 | 1950 | 2100 |
*Do not use on hammer setting.
Thin Wall CNC Drills
Thinwall CNC Drills
Diameter (mm) | RPM | Feed Rate (mm/min) |
---|---|---|
6-10 | 2500-2800 | 30-50 |
11-20 | 2200-2500 | 30-50 |
21-30 | 2000-2200 | 30-50 |
31-40 | 1250-2000 | 30-50 |
41-50 | 1100-1200 | 30-50 |
- Must be used wet with sufficient water feed.
- Always check that tool holder is in good condition. Clean thread before loading any new Thin Wall CNC Drill.
- Enter stone slowly.
- Thin Wall CNC Drills must be used with central water feed.
- Drill granite/quartz (Engineered stone) in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
DL200 CNC Drills
DL-200 CNC Drills
Drill Diameter (mm) | RPM | Feed Rate (mm/min) |
---|---|---|
6-20 | 2500-4000 | 20-30 |
20-30 | 1800-2500 | 20-30 |
30-40 | 1000-1800 | 20-30 |
- It is essential that our DL200 drills are used with both good internal and external water feed, otherwise drill will “melt” and fail due to heat.
- Always check that tool holder is in good condition. Clean thread before loading any new DL200 CNC Drill.
- Enter stone slowly.
- DL200 Drills must be used with central water feed.
- Drill UCS/Sintered Stone in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
Fast-Cut Core Drills
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
12 | 4400 | 4900 |
16 | 4300 | 4730 |
20 | 2860 | 3146 |
22 | 2290 | 2540 |
25 | 2290 | 2540 |
28 | 1910 | 2380 |
30 | 1910 | 2380 |
35 | 1630 | 2180 |
40 | 1430 | 1910 |
45 | 1270 | 1690 |
50 | 1140 | 1470 |
- Must be used wet with sufficient central and external water feed.
- Clean thread and fitting before loading any new core drill.
- Enter stone slowly.
- Drill granite/quartz (Engineered stone) in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
MB Large Core Drills
All Dry/Wet Core Drills – Various
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
60 | 950 | 1270 |
70 | 810 | 1090 |
80 | 710 | 950 |
90 | 630 | 840 |
100 | 570 | 750 |
110 | 520 | 690 |
120 | 470 | 630 |
- Must be used wet with sufficient central and external water feed.
- Clean thread and fitting before loading any new core drill.
- Enter stone slowly.
- Drill granite/quartz (Engineered stone) in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
Monumental Mason Core Drills
All Dry/Wet Core Drills – Various
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
20 | 2000 | 2500 |
24 | 2000 | 2200 |
28 | 2000 | 2200 |
90 | 630 | 840 |
- Must be used wet with sufficient central and external water feed.
- Clean thread and fitting before loading any new core drill.
- Enter stone slowly.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
Solid Drill Bits
Drill Diameter (mm) | Recommended (RPM) | Maximum (RPM) | Feed Rate (mm/min) |
---|---|---|---|
5 | 8800 | 11740 | 35-40 |
6 | 8800 | 11740 | 35-40 |
8 | 8600 | 9460 | 35-40 |
10 | 5730 | 7640 | 35-40 |
12 | 4400 | 5870 | 35-40 |
*Wet use only.
Polishing
Copper Resin Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
WX2 Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
DX1 Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 2500-3500 | – |
3 Step Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
6 Step Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
Marble Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
Note: Only Metal grades (50-400) can be used dry.
Plain Paper Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
125 | 2000-3000 | 2000-3000 |
Velour Paper Polishing Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
125 | 2000-3000 | – |
Automatic Snail Edging Wheels
Diameter (mm)/Fitting | Pressure (Bar) | Feed Rate (mm/min) |
---|---|---|
125/Snail | 2-3 | 800-1200 |
*Wet use only with no oscillation.
Automatic QRS Edging Wheels
Automatic Edge Polishing Wheels – Various
Diameter (mm)/Fitting | Pressure (Bar) | Feed Rate (mm/min) |
---|---|---|
125/QRS | 2-3 | 800-1200 |
*Wet use only with no oscillation.
Radial Arm Polishing System (RAPS)
Keep RAPS discs moving when in contact with stone surface, as if left stationary in one place stone can overheat, burn and or leave swirl marks particularly on quartz/engineered stone, which can be difficult to remove.
Also when polishing near or close to the edge of the stone, the RAPS disc mustn’t go more than 30% maximum of its diameter over the edge, as this can tip the disc and damage/break off the diamond segments.
Must be used wet.
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
250 | – | 500 |
Diamond Polishing Drums
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
50/75 | 1500-2000 | 3000-4000 |
Drainer Groove Polishing Wheels
Diameter/Disc Type (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
100mm x r5 | 1100 | 2000 |
100mm x r6.35 | 1100 | 2000 |
*Wet use only.
Grinding
Copper Resin Discs
Diameter (mm) | Dry Use (RPM) | Wet Use (RPM) |
---|---|---|
100 | 1500-2000 | 3000-4000 |
Diamond Cup Wheels
Diameter/Grade (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
100/Coarse | 3000-4000 | 11000 |
100/Medium | 3000-4000 | 11000 |
100/Fine | 3000-4000 | 11000 |
Flaring Cup Wheels
Prior to fitting the Cup Wheels directly onto the M14 spindle of the grinder polisher, check that there are no cracks, damage or hair line fractures to the resin. If there is any evidence of damage do not use – throw it away immediately, as this product can potentially be very dangerous if abused or run too fast.
Recommended (RPM) | Maximum (RPM) |
---|---|
2000-3000 | 8500 |
Straight Cup Wheels
Prior to fitting the Cup Wheels directly onto the M14 spindle of the grinder polisher, check that there are no cracks, damage or hair line fractures to the resin. If there is any evidence of damage do not use – throw it away immediately, as this product can potentially be very dangerous if abused or run too fast.
Recommended (RPM) | Maximum (RPM) |
---|---|
2000-3000 | 8600 |
Semi Flex Discs
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
127 | 2500-3000 | 10000 |
178 | 2500-3000 | 6700 |
Fibre Discs
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
180 | 2500-4000 | 8500 |
Bridge Saw Milling Wheels
Diameter (mm) | Hard Granites (RPM) | Soft Granites (RPM) | Recommended Stock (mm) | Maximum Stock (mm) |
---|---|---|---|---|
350 | 1364 | 1637 | 5 | 10 |
400 | 1194 | 1433 | 5 | 10 |
Diamond Antiquing Wheels
Diameter (mm) | Maximum (RPM) |
---|---|
110 | 1800 |
130 | 1800 |
*Must be used wet
VB Drums
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
10 | 4000-5000 | 7500 |
20 | 4000-5000 | 7500 |
40 | 3000-4000 | 6500 |
50 | 3000-4000 | 6500 |
75 | 2000-3000 | 5500 |
Fluting Wheels
Dimensions (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
150 x 10 x r5 | 1500-2500 | 6400 |
Prior to fitting the Fluting Wheels directly onto grinder polisher spindle, check that there are no cracks, damage or hair line fractures to the resin. If there is any evidence of damage do not use – throw away immediately, as this product can potentially be very dangerous if abused or run too fast.
Recessed Drainer Stubbing Wheel
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
86 x 40 x 50+3 | 4300 | 600 | 2-3mm/Pass |
* wet use only
Profiling
MB Profile Wheels
Recommended (RPM) | Maximum (RPM) |
---|---|
3000-4000 | 6500 |
*Recommend grinding/removing sharp corners (top and bottom depending on edge profile) to help prolong the life of the wheel.
**Wet use only.
VB Profile Wheels
Recommended (RPM) | Maximum (RPM) |
---|---|
3000-4000 | 6500 |
*Recommend grinding/removing sharp corners (top and bottom depending on edge profile) to help prolong the life of the wheel.
Milling Crown
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
20 x 20 x M12 | 6000-8000 | 1000-1500 | 0.5-1.0 |
*Ensure bottom of Router Crown is below the bottom of the slab when making final pass, to avoid “blow-out” particularly on more sugary stones.
**Wet use only.
Hob Cut-Out Router
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Stock Removal Rate (mm/min) |
---|---|---|---|
10 x 15 x 10 Shank | 6000-8000 | 1000-1500 | 0.5 – 1.0 |
*Ensure bottom of Router Crown is below the bottom of the slab when making final pass, to avoid “blow-out” particularly on more sugary stones.
**Wet use only.
Bridge Saw Drainer Groove Wheel
Diameter (mm) | Recommended (RPM) | Maximum (RPM) |
---|---|---|
400 | 1194 | 2300 |
VB Drainer Groove Wheels
Recommended (RPM) | Maximum (RPM) |
---|---|
3000-4000 | 6500 |
Sculpture Burrs
Dimensions (mm) | Recommended (RPM) |
---|---|
60 OAL x 6 | 8000-12000 |
CNC Tooling
Thin Wall CNC Drills
Thinwall CNC Drills
Diameter (mm) | RPM | Feed Rate (mm/min) |
---|---|---|
6-10 | 2500-2800 | 30-50 |
11-20 | 2200-2500 | 30-50 |
21-30 | 2000-2200 | 30-50 |
31-40 | 1250-2000 | 30-50 |
41-50 | 1100-1200 | 30-50 |
- Must be used wet with sufficient water feed.
- Always check that tool holder is in good condition. Clean thread before loading any new Thin Wall CNC Drill.
- Enter stone slowly.
- Thin Wall CNC Drills must be used with central water feed.
- Drill granite/quartz (Engineered stone) in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
DL200 CNC Drills
DL-200 CNC Drills
Drill Diameter (mm) | RPM | Feed Rate (mm/min) |
---|---|---|
6-20 | 2500-4000 | 20-30 |
20-30 | 1800-2500 | 20-30 |
30-40 | 1000-1800 | 20-30 |
- It is essential that our DL200 drills are used with both good internal and external water feed, otherwise drill will “melt” and fail due to heat.
- Always check that tool holder is in good condition. Clean thread before loading any new DL200 CNC Drill.
- Enter stone slowly.
- DL200 Drills must be used with central water feed.
- Drill UCS/Sintered Stone in one pass, do not peck drill.
- Re-sharpen with dressing stick (reducing 50% RPM) if/when drill glazes.
Parallel Routers
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) |
---|---|---|
20 x 40 x 5 seg | 5000-6000 | 250-400 |
20 x 45 x 5 seg | 5000-6000 | 250-400 |
*Reduce spindle speed for first 2000mm when router is new.
**Wet use only.
HS2 Parallel Router
- Check cone conditions: must be clean without rust. Pull stud should not be too worn
- Use a reasonable number of suction cups and double-check they are all the very same height in order to avoid vibrations
- Internal water is very important: keep water filter clean.
DL2 Parallel Routers
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) |
---|---|---|
D20 x L25 x 8 seg | 4000-5000 | 150-250 |
D20 x L40 x 5 seg | 4000-5000 | 150-250 |
It is essential when machining UCS (Ultra Compact Surfaces) and porcelain type materials that a sufficient number of suction/vacuum cups are used to hold the stone in place and to reduce vibration. They should be positioned on all sides of the sink cut-out, including front and back rails (use clamps if available) and use at least three or four suction cups inside the bowl to secure the cut-out.
When installing our DL2 Routers set tool height so the bottom of the diamond segments clear the underside of the stone.
*Reduce spindle speed for first 2000mm when router is new (minimum 150mm/min feed rate).
**Must be used wet with ample water feed.
Quartzite Parallel Router
Dimensions (mm) | Spindle Speed (RPM) | Feed Rate (mm/min) |
---|---|---|
D22 x L45 x 7 Segments | 5500-7500 | 200-500 |
It is essential when machining any hard/problematic stones that a sufficient number of suction/vacuum cups are used to hold the material in place and to reduce vibration. These should be positioned on all sides of the sink cut-out, including front and back rails (use clamps if available) and use at least three or four suction cups inside the bowl to secure the cut-out.
When installing our Quartzite Router set tool height so the bottom of the diamond segments clear the underside of the stone.
*Reduce spindle speed for the first 2000mm when the router is new (minimum 150mm/min feed rate) and gradually increase in increments of +10% steps,ensuring Amps reading and sound of the router is okay whilst in use.
**Must be used wet with ample water feed.
Plunging Parallel Router
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Max Stock Removal (mm) |
---|---|---|---|
20 x 40 x 5 seg | 5000-6000 | 700-900 | 2mm/Pass |
*Reduce spindle speed for first 2000mm when router is new.
**Wet use only.
VB CNC Parallel Router
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) |
---|---|---|
18D x 40C/L | 6000-7000 | 600-1200 |
*Wet use only.
Hob Cut-Out Router
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Stock Removal Rate (mm/min) |
---|---|---|---|
10 x 15 x 10 Shank | 6000-8000 | 1000-1500 | 0.5 – 1.0 |
*Ensure bottom of Router Crown is below the bottom of the slab when making final pass, to avoid “blow-out” particularly on more sugary stones.
**Wet use only.
Jumbo Z70 Profile Wheels
Position | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
Pos.1 | 4000-5500 | 400-600 | 1.0 |
Pos.2 | 4000-5500 | 400-800 | 0.5-0.6 |
Pos.3 | 4000-5500 | 400-800 | 0.2-0.3 |
Pos.4 | 4000-4500 | 400-800 | 0.1 |
Pos.5 | 2500 | 600-1000 | 0.05 |
Pos.6 | 2500 | 600-1000 | 0.05 |
Pos.7 | 2500 | 600-1000 | 0.05 |
*Can be used with or without oscillation.
**Wet use only.
Jumbo Z70 Mini Profile Wheels
Position | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
Pos.1 | 4000-5500 | 400-600 | 1.0 |
Pos.2 | 4000-5500 | 400-800 | 0.5-0.6 |
Pos.3 | 4000-5500 | 400-800 | 0.2-0.3 |
Pos.4 | 4000-4500 | 400-800 | 0.1 |
Pos.5 | 2500 | 600-1000 | 0.05 |
Pos.6 | 2500 | 600-1000 | 0.05 |
Pos.7 | 2500 | 600-1000 | 0.05 |
*Can be used with or without oscillation.
**Wet use only.
CNC Profile Wheels
A23 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]A33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 4000-4500 | 500-800 | 2.0 |
Pos.2/120 | 4000-4500 | 800-1200 | 0.5-0.6 |
Pos.3/250 | 4000-4500 | 800-1200 | 0.2-0.3 |
Pos.4/600 | 4000-4500 | 800-1200 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]B33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 4000-4500 | 500-800 | 2.0 |
Pos.2/120 | 4000-4500 | 800-1200 | 0.5-0.6 |
Pos.3/250 | 4000-4500 | 800-1200 | 0.2-0.3 |
Pos.4/600 | 4000-4500 | 800-1200 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]F23 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 4000-4500 | 500-800 | 2.0 |
Pos.2/120 | 4000-4500 | 800-1200 | 0.5-0.6 |
Pos.3/250 | 4000-4500 | 800-1200 | 0.2-0.3 |
Pos.4/600 | 4000-4500 | 800-1200 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]F33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 4000-4500 | 500-800 | 2.0 |
Pos.2/120 | 4000-4500 | 800-1200 | 0.5-0.6 |
Pos.3/250 | 4000-4500 | 800-1200 | 0.2-0.3 |
Pos.4/600 | 4000-4500 | 800-1200 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]T23 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]T33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]TRAP33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]V33 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 4000-4500 | 500-800 | 2.0 |
Pos.2/120 | 4000-4500 | 800-1200 | 0.5-0.6 |
Pos.3/250 | 4000-4500 | 800-1200 | 0.2-0.3 |
Pos.4/600 | 4000-4500 | 800-1200 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]Z35 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="tab"]Z45 Profile Wheels

Pos. 1-4 Metal Bond, Pos. 5-7 Resin Bond
Position/Grade | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
Pos.1/40 | 5000-5500 | 400-800 | 2.0 |
Pos.2/120 | 5000-5500 | 500-800 | 0.5-0.6 |
Pos.3/250 | 5000-5500 | 500-800 | 0.2-0.3 |
Pos.4/600 | 5000-5500 | 500-800 | 0.1 |
Pos.5/800 | 2500 | 800-1200 | 0.05 |
Pos.6/1500 | 2500 | 800-1200 | 0.05 |
Pos.7/3000 | 2500 | 800-1200 | 0.05 |
*All Positions 1-7 are to be used with both central and external water feed.
[ctabs break="end"]Manual Vacuum/Suction Clamps
CNC Machine Vacuum/Suction Cup Heights
Machine Type | Height (mm) |
---|---|
Bavelloni | 124.50 |
Bimatech | 140 |
Breton | 90/150 |
CMS Brembana | 200 |
Cobalm | 120 |
Denver | 120 |
Intermac | 105 |
Intermac Plus | 213 |
Omag | 105 |
Prussiani | 240 |
Thibaut | 149 |
Rectangular Vacuum/Suction Cups
CNC Machine Vacuum/Suction Cup Heights
Machine Type | Height (mm) | Air Inlet (mm) |
---|---|---|
Bavelloni | 124.50 | 8 |
Bimatech | 140 | 10 |
Breton | 90/150 | 8 |
CMS Brembana | 200 | 6 |
CMS Concept | 100 | 6 |
Cobalm | 120 | 8 |
Denver | 120 | 8 |
Donatoni | 120 | 8 |
Intermac | 105 | 8 |
Intermac Plus | 213 | 8 |
Northwood | 105 | 8 |
Omag | 105 | 8 |
Park Industries | 105 | 8 |
Poseidon | 105 | 8 |
Prussiani | 240 | 8 |
Scandinvent | 200 | 6 |
Thibaut | 149 | 8 |
Corner/”L” Shaped Vacuum/Suction Cups
CNC Machine Vacuum/Suction Cup Heights
Machine Type | Height (mm) | Air Inlet (mm) |
---|---|---|
Bavelloni | 124.50 | 8 |
Bimatech | 140 | 10 |
Breton | 90/150 | 8 |
CMS Brembana | 200 | 6 |
CMS Concept | 100 | 6 |
Cobalm | 120 | 8 |
Denver | 120 | 8 |
Donatoni | 120 | 8 |
Intermac | 105 | 8 |
Intermac Plus | 213 | 8 |
Northwood | 105 | 8 |
Omag | 105 | 8 |
Park Industries | 105 | 8 |
Poseidon | 105 | 8 |
Prussiani | 240 | 8 |
Scandinvent | 200 | 6 |
Thibaut | 149 | 8 |
Square Vacuum/Suction Cups
CNC Machine Vacuum/Suction Cup Heights
Machine Type | Height (mm) | Air Inlet (mm) |
---|---|---|
Bavelloni | 124.50 | 8 |
Bimatech | 140 | 10 |
Breton | 90/150 | 8 |
CMS Brembana | 200 | 6 |
CMS Concept | 100 | 6 |
Cobalm | 120 | 8 |
Denver | 120 | 8 |
Donatoni | 120 | 8 |
Intermac | 105 | 8 |
Intermac Plus | 213 | 8 |
Northwood | 105 | 8 |
Omag | 105 | 8 |
Park Industries | 105 | 8 |
Poseidon | 105 | 8 |
Prussiani | 240 | 8 |
Scandinvent | 200 | 6 |
Thibaut | 149 | 8 |
Circular Vacuum/Suction Cups
CNC Machine Vacuum/Suction Cup Heights
Machine Type | Height (mm) | Air Inlet (mm) |
---|---|---|
Bavelloni | 124.50 | 8 |
Bimatech | 140 | 10 |
Breton | 90/150 | 8 |
CMS Brembana | 200 | 6 |
CMS Concept | 100 | 6 |
Cobalm | 120 | 8 |
Denver | 120 | 8 |
Donatoni | 120 | 8 |
Intermac | 105 | 8 |
Intermac Plus | 213 | 8 |
Northwood | 105 | 8 |
Omag | 105 | 8 |
Park Industries | 105 | 8 |
Poseidon | 105 | 8 |
Prussiani | 240 | 8 |
Scandinvent | 200 | 6 |
Thibaut | 149 | 8 |
Recessed Drainer Stubbing Wheel
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
86 x 40 x 50+3 | 4300 | 600 | 2-3mm/Pass |
* wet use only
Single Corner Breaker Wheel
Dimensions (mm) | Recommended (RPM) | Feed Rate (mm/min) |
---|---|---|
120 x 25 x 35 | 4000-5500 | 250-800 |
*Wet use only.
2 Stage Flute Wheels
Recommended (RPM) | Feed Rate (mm/min) | Statistical Wear | Adaptive Wear |
---|---|---|---|
1600 | 1000 | 12 | 14 |
*Wet use only.
Flute Routers
Diameter/Position (mm) | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
All/Pos.1 | 6000 | 400-600 | 1.0 |
All/Pos.2 | 6000 | 400-600 | 0.3 |
All/Pos.3 | 6000 | 400-600 | 0.1 |
*Wet use only.
PCD Engraving Tool
Dimensions(mm) | Recommended (RPM) | Feed Rate (mm/min) | Maximum Stock Removal (mm) |
---|---|---|---|
10 x 15 x 10 Shank | 6000-8000 | 1000-1500 | 2mm/Pass |
Adaptors
Back-Up Pads
Accessories
Health & Safety
Force™ 8 Half-Mask
Sound Stopper Ear Plugs
Glues & Colours
Stone-Stik Solid/Vertical Polyester Glues
Consistency | Smooth Paste |
---|---|
Mix Ratio | 2% – 4% BPO |
Gel Time | 3 – 5 minutes |
Cure Time | 20 minutes |
Shelf Life | 1 year |
Location | Indoor |
Materials | Natural & Engineered Porous Stone |
Applications | Seaming, Laminating Rodding, Crack / Chip Repair |
Be sure to TEST each substrate for bonding and appearance prior to the actual application.
Use: To achieve the best results, the contact surfaces must be thoroughly cleaned and dried. Before adding the hardener, the resin may be tinted with GTS Colouring Paste to match the colour of the stone. The resin is then thoroughly mixed with 2%-4% of the white paste hardener (BPO) by weight. At a temperature of 70°F (21°C), the mixture stays workable for 4-6 minutes. Higher temperatures shorten the working time and lower temperatures extend the working time. After 20-30 minutes, the adhesive is fully cured and work can continue with the stone. For indoor use only. Do NOT store above 75°F (24°C)
Storage: Store indoors at room temperature. Do NOT store above 75°F (24°C). High heat and cold temperatures will adversely affect the shelf life. Avoid storage in direct sunlight and where freeze/thaw conditions may exist.
Vehicle Temperature
Outside Temp | Inside Temp | Inside Temp |
---|---|---|
10 mins | 30 mins | |
70°F (21°c) | 89°F (32°c) | 104°F (40°c) |
75°F (24°c) | 94°F (34°c) | 109°F (43°c) |
80°F (27°c) | 99°F (37°c) | 114°F (46°c) |
85°F (29°c) | 104°F (40°c) | 119°F (49°c) |
90°F (32°c) | 109°F (43°c) | 124°F (51°c) |
95°F (35°c) | 114°F (46°c) | 129°F (54°c) |
Stone-Stik Solid/Vertical Glues Safety Data Sheets (SDS)
Pearl Solid/Vertical Vinylester Glue
Consistency | Smooth Paste |
---|---|
Mix Ratio | 1% – 3% BPO |
Gel Time | 3 – 5 minutes |
Cure Time | 20 minutes |
Shelf Life | 1 – 2 years |
Location | Indoor |
Materials | Natural & Engineered Stones |
Applications | Seaming, Laminating, Mitre Joints, Crack/Chip Repair |
Be sure to TEST each substrate for bonding and appearance prior to the actual application.
Use: To achieve the best results, the contact surfaces must be thoroughly cleaned and dried. Before adding the hardener, the resin may be tinted with GTS Colouring Paste to match the colour of the stone. The resin is then thoroughly mixed with no more than 1%-3% of the white paste hardener (BPO) by weight. At a temperature of 70°F (21°C), the mixture stays workable for 4-6 minutes. Higher temperatures shorten the working time and lower temperatures extend the working time. After 20-30 minutes, the adhesive is fully cured and work can continue with the stone. For white marble, be sure to test for shadowing and colour match prior to application. For indoor use only. Do NOT store above 75°F (24°C).
Storage: Store indoors at room temperature. Do NOT store above 75°F (24°C). High heat and cold temperatures will adversely affect the shelf life. Avoid storage in direct sunlight and where freeze/thaw conditions may exist.
Vehicle Temperature
Outside Temp | Inside Temp | Inside Temp |
---|---|---|
10 mins | 30 mins | |
70°F (21°c) | 89°F (32°c) | 104°F (40°c) |
75°F (24°c) | 94°F (34°c) | 109°F (43°c) |
80°F (27°c) | 99°F (37°c) | 114°F (46°c) |
85°F (29°c) | 104°F (40°c) | 119°F (49°c) |
90°F (32°c) | 109°F (43°c) | 124°F (51°c) |
95°F (35°c) | 114°F (46°c) | 129°F (54°c) |
Stone-Stik Pearl Solid/Vertical Glue Safety Data Sheets (SDS)
Stone-Stik Liquid Polyester Glue
Consistency | Syrup |
---|---|
Mix Ratio | 2% – 4% BPO |
Gel Time | 3 – 5 minutes |
Cure Time | 20 minutes |
Shelf Life | 1 year |
Location | Indoor |
Materials | Natural & Engineered Porous Stones |
Applications | Laminating, Rodding, Crack / Chip Repair |
Be sure to TEST each substrate for bonding and appearance prior to the actual application.
Use: To achieve the best results, the contact surfaces must be thoroughly cleaned and dried. Before adding the hardener, the resin may be tinted with GTS Colouring Paste to match the colour of the stone. The resin is then thoroughly mixed with 2%-4% of the white paste hardener (BPO) by weight. At a temperature of 70°F (21°C), the mixture stays workable for 4-6 minutes. Higher temperatures shorten the working time and lower temperatures extend the working time. After 20-30 minutes, the adhesive is fully cured and work can continue with the stone. For indoor use only. Do NOT store above 75°F (24°C)
Storage: Store indoors at room temperature. Do NOT store above 75°F (24°C). High heat and cold temperatures will adversely affect the shelf life. Avoid storage in direct sunlight and where freeze/thaw conditions may exist.
Vehicle Temperature
Outside Temp | Inside Temp | Inside Temp |
---|---|---|
10 mins | 30 mins | |
70°F (21°c) | 89°F (32°c) | 104°F (40°c) |
75°F (24°c) | 94°F (34°c) | 109°F (43°c) |
80°F (27°c) | 99°F (37°c) | 114°F (46°c) |
85°F (29°c) | 104°F (40°c) | 119°F (49°c) |
90°F (32°c) | 109°F (43°c) | 124°F (51°c) |
95°F (35°c) | 114°F (46°c) | 129°F (54°c) |
Stone-Stik Liquid/Horizontal Glue Safety Data Sheets (SDS)
Stone-Stik Colour Pastes
Vehicle Temperature
Outside Temp | Inside Temp | Inside Temp |
10 mins | 30 mins | |
70°F (21°c) | 89°F (32°c) | 104°F (40°c) |
75°F (24°c) | 94°F (34°c) | 109°F (43°c) |
80°F (27°c) | 99°F (37°c) | 114°F (46°c) |
85°F (29°c) | 104°F (40°c) | 119°F (49°c) |
90°F (32°c) | 109°F (43°c) | 124°F (51°c) |
95°F (35°c) | 114°F (46°c) | 129°F (54°c) |
Stone-Stik Paste Quartz Colour Match Ratios
[ctabs break="start"][ctabs break="tab"]Silestone
Stone Type |
Black % |
White % |
Ochre % |
Red-Brown % |
Brown % |
Red % |
Blue % |
Green % |
Aluminium Nube |
16.667 |
72.222 |
5.556 |
0.000 |
0.000 |
0.000 |
5.556 |
0.000 |
Amarillo Palmira |
1.942 |
53.398 |
33.981 |
0.000 |
9.709 |
0.971 |
0.000 |
0.000 |
Amazon |
14.286 |
47.619 |
0.000 |
0.000 |
38.095 |
0.000 |
0.000 |
0.000 |
Azul Ugarit |
0.730 |
64.234 |
18.248 |
0.000 |
16.058 |
0.730 |
0.000 |
0.000 |
Blanco Capri |
2.663 |
50.000 |
29.290 |
18.047 |
0.000 |
0.000 |
0.000 |
0.000 |
Blanco Dune |
10.303 |
86.061 |
3.636 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
Blanco Norte |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
Blanco Zeus |
0.313 |
94.357 |
0.000 |
0.000 |
5.329 |
0.000 |
0.000 |
0.000 |
Brazillian Brown Leather |
10.526 |
42.105 |
5.263 |
0.000 |
42.105 |
0.000 |
0.000 |
0.000 |
Carbono |
2.466 |
90.411 |
3.562 |
0.000 |
2.466 |
0.000 |
1.096 |
0.000 |
Ebony Pearl |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
Eros Stellar |
0.000 |
9.827 |
35.838 |
28.902 |
0.000 |
25.434 |
0.000 |
0.000 |
Gedatsu |
13.000 |
23.000 |
0.000 |
63.000 |
1.000 |
0.000 |
0.000 |
0.000 |
Gedatsu Leather |
14.286 |
47.619 |
0.000 |
0.000 |
38.095 |
0.000 |
0.000 |
0.000 |
Gris Expo |
15.894 |
70.861 |
7.947 |
0.000 |
4.636 |
0.662 |
0.000 |
0.000 |
Haiku |
2.663 |
50.000 |
29.290 |
18.047 |
0.000 |
0.000 |
0.000 |
0.000 |
Kensho |
4.478 |
86.567 |
2.985 |
0.000 |
4.478 |
0.000 |
1.493 |
0.000 |
Kona Beige |
0.730 |
64.234 |
18.248 |
0.000 |
16.058 |
0.730 |
0.000 |
0.000 |
Marina Stellar |
15.385 |
0.000 |
0.000 |
0.000 |
0.000 |
5.769 |
78.846 |
0.000 |
Maron Jupiter |
13.000 |
23.000 |
0.000 |
0.000 |
63.000 |
1.000 |
0.000 |
0.000 |
Negro Anubis |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
Negro Stellar |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
Negro Tebas |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
Rojo Eros |
0.000 |
9.827 |
35.838 |
28.902 |
0.000 |
25.434 |
0.000 |
0.000 |
Satori |
13.846 |
32.308 |
0.000 |
4.615 |
49.231 |
0.000 |
0.000 |
0.000 |
Steel |
44.444 |
0.000 |
0.000 |
0.000 |
55.556 |
0.000 |
0.000 |
0.000 |
Tegris Sand |
2.663 |
50.000 |
29.290 |
18.047 |
0.000 |
0.000 |
0.000 |
0.000 |
Unsui |
10.526 |
42.105 |
5.263 |
0.000 |
42.105 |
0.000 |
0.000 |
0.000 |
Yukon |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
Caesarstone
Stone Type |
Black % |
White % |
Ochre % |
Red-Brown % |
Brown % |
Red % |
Blue % |
Green % |
2141 Blizzard |
0.073 |
99.436 |
0.491 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
2370 Cashmere |
4.369 |
58.738 |
12.136 |
0.000 |
24.757 |
0.000 |
0.000 |
0.000 |
2400 Chiltern |
1.010 |
82.828 |
15.152 |
0.000 |
0.404 |
0.606 |
0.000 |
0.000 |
6310 Coffee Bean |
4.545 |
6.818 |
0.000 |
13.636 |
75.000 |
0.000 |
0.000 |
0.000 |
2020 Cubanite Grey |
2.708 |
89.998 |
4.458 |
2.836 |
0.000 |
0.000 |
0.000 |
0.000 |
2200 Desert Limestone |
0.381 |
94.083 |
4.255 |
1.281 |
0.000 |
0.000 |
0.000 |
0.000 |
3200 Desert Sand |
1.646 |
88.066 |
7.819 |
0.000 |
2.058 |
0.412 |
0.000 |
0.000 |
7100 Ebony Reflections |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
4330 Ginger |
12.174 |
58.606 |
10.129 |
0.000 |
17.365 |
0.000 |
1.726 |
0.000 |
2220 Ivory |
10.303 |
86.061 |
3.636 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
4250 Jerusalem Sand |
0.468 |
76.815 |
17.799 |
4.918 |
0.000 |
0.000 |
0.000 |
0.000 |
3100 Jet Black |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
2350 Latte |
1.117 |
81.006 |
7.263 |
0.000 |
10.615 |
0.000 |
0.000 |
0.000 |
4141 Misty Carrara |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
7150 Mosiaco Carbono |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
6600 Nougat |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
3141 Osprey |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
4030 Oyster |
15.894 |
70.861 |
7.947 |
0.000 |
4.636 |
0.662 |
0.000 |
0.000 |
7141 Quartz Reflection |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
4120 Raven |
8.140 |
50.000 |
0.000 |
16.279 |
20.930 |
0.000 |
4.651 |
0.000 |
7450 Ruby Reflections |
0.000 |
0.000 |
47.368 |
0.000 |
0.000 |
52.632 |
0.000 |
0.000 |
2750 Sage |
1.724 |
55.172 |
0.000 |
0.000 |
18.966 |
0.000 |
0.000 |
24.138 |
2003 Titanium |
6.073 |
53.555 |
33.281 |
0.000 |
7.091 |
0.000 |
0.000 |
0.000 |
Compac Quartz
Stone Type |
Black % |
White % |
Ochre % |
Red-Brown % |
Brown % |
Red % |
Blue % |
Green % |
Alaska |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
Azabache |
79.032 |
0.000 |
0.000 |
0.000 |
20.000 |
0.000 |
0.000 |
0.000 |
Coco |
10.303 |
86.061 |
3.636 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
Cherokee |
4.545 |
6.818 |
0.000 |
13.636 |
75.000 |
0.000 |
0.000 |
0.000 |
Luno |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
Nocturno |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
Passion |
0.000 |
0.000 |
47.368 |
0.000 |
0.000 |
52.632 |
0.000 |
0.000 |
Rubi |
0.000 |
0.000 |
47.368 |
0.000 |
0.000 |
52.632 |
0.000 |
0.000 |
Snow |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
Spiris |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
Venecia |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
Quarella
Stone Type |
Black % |
White % |
Ochre % |
Red-Brown % |
Brown % |
Red % |
Blue % |
Green % |
Nero |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
Lapic |
15.385 |
0.000 |
0.000 |
0.000 |
63.000 |
1.000 |
0.000 |
0.000 |
Marron Luciente |
4.545 |
6.818 |
0.000 |
13.636 |
75.000 |
0.000 |
0.000 |
0.000 |
Negro Luciente |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
New Diamonte |
0.578 |
98.578 |
0.616 |
0.228 |
0.000 |
0.000 |
0.000 |
0.000 |
Nina |
0.625 |
95.000 |
2.188 |
0.625 |
1.563 |
0.000 |
0.000 |
0.000 |
Nortturno Blanco |
79.032 |
0.000 |
0.000 |
0.000 |
20.968 |
0.000 |
0.000 |
0.000 |
Toramalina |
84.906 |
0.000 |
0.000 |
0.000 |
0.000 |
15.094 |
0.000 |
0.000 |